Best answer: Where is the main fuse on a motorcycle?

Normally you would install the main fuse on the live side of the battery in-line with the wire which goes from the battery and up to the ammeter connections for distribution to the lights and other accessories.

Where is the main fuse located?

If the blown fuse is a main fuse, the main fuse block is usually located at the top of the fuse box.

Are motorcycle fuses the same as car fuses?

Motorcycle fuses and car fuses are the same fuse type, but vehicle owners replacing a fuse need to pay attention to the fuse amperage used.

Why am I not getting power to my motorcycle?

Take the battery to an auto parts store and have them test it. If the battery fails their test, replace the battery. Next, check the main fuse, usually on the same cable as the positive battery connector. … Then check the fuses in fuse box, doing as with the main fuse if any are blown.

What amp fuse do I need?

Plugs for appliances rated between about 700 watts and 3000 watts (the maximum rating of a wall socket) should be fitted with a 13-amp fuse (coloured brown). For example: 13A Fuse – Washing machine, dishwasher, microwave, kettle, toaster, iron.

IT IS INTERESTING:  What is the best temperature to ride a motorcycle?

What are the 3 types of fuses?

Different Types of Fuses – Constriction, Working & Characteristics

  • DC Fuses.
  • AC Fuses.
  • Cartridge Fuses.
  • D – Type Cartridge Fuse.
  • HRC (High Rupturing Capacity) Fuse or Link Type Cartridge Fuse.
  • High Voltage Fuses.
  • Automotive, Blade Type & Bolted Type Fuses.
  • SMD Fuses (Surface Mount Fuse), Chip , Radial, and Lead Fuses.

What will cause a fuse to keep blowing?

There are two conditions that can cause a fuse to blow. First, and most commonly, when too many lights or plug-in appliances draw power from the circuit, it can overload the capacity of the fuse and cause the metal ribbon inside the fuse to melt through.

How can you tell if a screw fuse is blown?

Look at the fuse wire. If there is a visible gap in the wire or a dark or metallic smear inside the glass then the fuse is blown and needs to be replaced. If you cannot see whether the fuse is blown, follow steps 4 and 5.

What happens if I put a 15 amp fuse in a 10 amp slot?

You can, it will may immediately blow, but it won’t hurt anything other than the fuse. … What you don’t want to do is use a higher amp fuse or something like a jumper wire. That could damage the wiring and start a fire.

Why does my motorcycle fuse keeps blowing?

A motorcycle fuse blows when the current draw on a circuit exceeds the amperage rating of the fuse. In order to protect the wiring in that circuit from melting, the fuse will blow so no permanent damage is done to your motorcycle wires or accessories.

IT IS INTERESTING:  You asked: What is the best scrambler motorcycle?

Why do my bike fuses keep blowing?

When a fuse repeatedly blows, it’s either the wrong amperage fuse or a faulty circuit. If you’re positive you have the right amperage fuse in it [check your owners manual] then it has to be a faulty circuit.

When I try to start my motorcycle it just clicks?

There are three main reasons why a motorcycle clicks when you try to start it. The first and most common reason is because of a dead battery. The second reason could be due to a bad starter. The third most common but less likely reason the motorcycle is clicking could be due to a seized engine.

What is Bike kill switch?

The kill switch or emergency switch or engine shut off/cut off (switch) (even the naming is ambiguous) is a red switch located on the right handle bar of just about every modern motorcycle commercially manufactured today. It is a safety feature that can be used to cut power to the engine in the event of an emergency.

Bikepost