Some chains are directional and any logos or printed letters should face out towards the mechanic on the drive side. … Master link chains have inner plates on both ends so you can lead with either end for chains that use a master link. Feed the chain through the rear derailleur as shown.
Are bike chains directional?
Some bicycle chains are directional. SRAM chains are not directional; however, Shimano chains are (the engravings on the chain must be facing away from the bike).
What happens if you put a bike chain on backwards?
If you remove a well worn chain and install it in the reverse direction, you’ll end up with a mysterious skip in your drivetrain. … There are two exceptions – if the chain has an “inside”, i.e. points to the cogs, and “outside”, i.e. never contacts cogs, except the pulley of the rear derailleur.
Are Shimano chains directional?
Each of the four plates, inner and outer, are shaped differently to act in a certain way relative to their position with the front chain rings or rear cogs as you shift up or down through the gear range. This means that the HG-X chain is directional. … The Shimano CN-HG900 Chain is directional and 11-speed specific.
What is a non directional chain?
Non-directional chains are just that, non-directional. It doesn’t matter how you install or re-install them. As to using multiple chains to increase cassette longevity, that depends on the cost of both your chains and cassettes.
How do you remove a mountain bike chain without a master link?
If you have a standard chain with no master link: Seat the chain in the chain tool, with the pin of the chain tool aligned with a pin in the chain. Turn the handle of the chain tool until you push the pin out far enough that you can break the chain.
Is there a difference between road and MTB chain?
There is no such thing as a “road bike” or “mountain bike” chain, and there is actually very little difference in any bicycle chain except for construction design, and whether they are made of steel or titanium.
How often should I change my bike chain?
To avoid this accelerated wear of your cassette and chainrings, a general rule of thumb is to replace your bike’s chain every 2,000 miles. Mind you, this is just a starting point. No two chains will wear at exactly the same rate because no two riders treat their chains the same.
How do I know my bike chain size?
Begin by counting the number of teeth on the largest front sprocket and largest rear. These numbers are often printed right on the sprockets and cogs. Next, measure the distance between the middle of the crank bolt to the rear axle. This is also the chain stay length.
Do all bike chains have a master link?
Not all bikes have master rivets. If your bike has a derailleur, it’s unlikely that your chain will have a master link. Bikes that typically do have chains with master links are BMX bikes and one- or three-speed town bikes with internal gears. … If the width is 1/8 inch, your chain should have a master rivet.
Does bicycle chain make a difference?
Chain wear in itself does not increase resistance. Chain/cassette wear may impact shifting performance, but should not have any noticeable effect when you are in gear. The main danger of worn chain/cassette is skipping of the chain.
What is the difference between HG and IG chains?
The HG chain is a narrower chain meant for 8-9 speed drive trains. The IG chain is wider and meant for 6,7,8 speed drive trains.
Which side of chain faces out?
Some chains are directional and any logos or printed letters should face out towards the mechanic on the drive side. The process for routing the chain is the same for either master link or connecting rivet chains, just make sure to lead with outer plates if using a connecting rivet chain.
Are all Shimano 11 speed chains the same?
Shimano and SRAM 11-speed chains are not cross-compatible; if you have a Shimano 11-speed drivetrain, you need a Shimano 11-speed chain. We sell the Shimano CN-HG701 11 Speed Chain Ultegra/XT and the slightly lighter Shimano Dura-Ace/XTR CN-HG901 11-Speed Chain.